钨中空位及其团簇的能量学和动力学性质参数

在总结前人钨中空位及其团簇的能量学和动力学行为的研究成果基础上，采用第一性原理方法系统计算了钨中空位及其团簇的结合能和扩散能垒。研究发现，交换关联泛函PW91和PBE较PBEsol、AM05和LDA更适合用于计算钨空位的能量学性质。基于第一性原理计算结果对文献中单空位形成能、双空位作用性质等争议性问题进行了讨论，并对钨经验势进行了评估。研究结果表明，钨中孤立单空位间总是相互排斥，而空位团簇（V_n>3）对单空位具有很强的吸引作用，其结合能随着所含空位个数增多呈现波动性增大的趋势。空位团簇稳定结构可通过最小化Wigner-Seitz表面积来确定，其结合能与V_n与V_n-1之间的Wigner-Seitz面积之差呈正比。     

Comparison between fluctuation of floating potential gradient and velocity of blob structure on HL-2A tokamak

Several results based on the Langmuir probes' data on the HL-2A tokamak are presented. The blob structures' radial and poloidal drift velocities, estimated by the gradient of floating potential and by time delay evaluation, are compared in different line-averaged density and electron cyclotron resonance heating conditions. A positive correlation is observed in the comparison between blobs' radial velocity estimated by the two methods mentioned above, regardless of the situation differences mentioned above. Correlation is also observed in the comparison between the blobs' poloidal velocity estimated by the two methods in different situations, while a shift due to the different line-averaged density is observed. These results imply that the radial gradient of floating potential may have some value as a reference during data analysis in low-parameter discharge.     

针刺复合生态土工布的制备及植生性能研究

以黏胶短纤维和再生植物纤维为主要原料,采用短纤维干法成网-针刺加固工艺,在针刺密度为60～160针/cm2、针刺深度为3.5～ 12.0 mm、针刺频率为720～ 940次/min的条件下,制备单位面积质量在196～979g/m2、厚度在3.6～ 14.4 mm、再生植物纤维质量分数在39.6％ ～ 70.9％的针刺复合生态土工布,用于植生护坡.性能测试和植物种植试验结果表明:针刺复合生态土工布具有较好的力学性能和吸水保水性能,且对植物的生长具有良好的促进作用;随着针刺复合生态土工布单位面积质量的增加,其力学性能增加,吸水保水性能变好,发芽率、植株高度和植株质量也均呈现出增加的趋势.     

改进的遗传算法在同步器优化中的应用

汽车同步器是自动变速器的重要组成部分.对同步器的模拟优化能为同步器的设计生产提供重要的参考.为了获得一个较好的优化效果,提出了一种改进的遗传算法.通过对遗传算法选择过程的标准进行了改进,结合适应度函数与染色体之间差异,形成一种新的适应度函数.该函数同时考虑了选择压力和物种多样性.通过对函数中两个常量的调整,可以使算法在不同情况下可以有不同的偏重.引入两种典型测试函数的分别从高纬度变量和低纬度变量进行试验,分析改进算法中两个影响因子的作用.并与几类遗传算法进行比较,结果表明该改进的遗传算法能更快更稳定的找到较优的解.最后将改进选择策略结合自适应遗传算法对同步器进行优化,证明了该选择策略具有良好的鲁棒性和实效性.     

聚合物对旋流器内油滴聚结与分离效率的影响

为了研究聚合物对水力旋流器内油滴聚结与分离效率的影响规律,以螺旋导流内锥式旋流器为研究对象,利用群体平衡模型(PBM)方法对不合聚与含聚0.5‰工况下油水两相在旋流器内的速度场、黏度场、油滴聚结、运移特性及分离效率进行数值分析,并通过实验验证.结果 表明:聚合物的加入增大了水相黏度,使油滴在旋流器内最大停留时间与轴向运动距离增加,增加了油滴碰撞聚结的机会,但降低轴心处油滴向上运动的轴向速度,使油滴无法快速从溢流口流出,最终从底流口流出,增加油水分离的难度.与不合聚时相比,含聚0.5‰工况下,轴心处的油滴粒径与含油体积分数较高,但简化分离效率由99.79％降低至94.72％.通过马尔文粒度仪对两种工况下入口与出口的油滴粒径进行测试,含聚0.5‰时溢流与底流口油滴粒径高于不合聚时,验证了模拟的准确性.     

稀土灼烧过程温湿度场仿真分析

影响稀土灼烧工艺的因素十分复杂,关系产品质量稳定及能耗,现行工艺存在优化空间。通过剖析灼烧窑中温度和湿度分布状况,运用κ-ε双方程湍流模型、流体传热、多孔介质传热等理论,按特定组分运输模式,建立灼烧过程质量、动量和能量耦合传递数学模型。设置不同边界导入Fluent环境对数学模型进行仿真试验,完成数据处理实现工艺参数优化。结果表明所建模型能准确反映灼烧窑中温湿度场分布及变化,且最终仿真结果与实际灼烧后的产品湿度含量相符合。     

悬浮法PVC树脂粒径异常问题的解决

分析了聚合过程中影响悬浮法聚氯乙烯树脂粒径的因素,从分散体系、聚合条件、聚合温控3个方面采取了改进措施.     

三聚硫氰酸单钠盐的制备及应用研究进展

三聚硫氰酸单钠盐是一种新型的多官能团化精细化学品。介绍了三聚硫氰酸单钠盐的制备方法,以及其在橡胶硫化、橡胶与金属的硫化粘合等领域的应用研究进展。     

Design and fabrication of lutetium aluminum silicate glass and nanostructured glass for radiation detection

Flexible scintillating fiber plays an important role in X-ray radiation monitoring and high-resolution medical imaging, while construction of scintillating fiber derived from the commercial material system meet with limited success. Here, we report the design and successful fabrication of the Ce-activated lutetium aluminum silicate glass, nanostructured glass, and fiber, and explore their scintillating properties. The scintillating glass with optimized composition and optical properties is determined. The crystallization behavior of lutetium aluminum silicate glass is studied and the nanostructured glass embedded with orthorhombic Lu₂Si₂O₇ phase is successfully constructed for the first time. Importantly, the crystalline layer thickness of the nanostructured glass can be finely tuned and ~172.89% enhancement in the scintillating performance can be achieved. Furthermore, the fiber with large sized core is fabricated and its radiation response properties are tested. The results show that it exhibits high sensitivity and its scintillating emission is lineally dependent on the X-ray power, indicating the potential application for radiation detection.